The Basics of Plumbing Skills When Installing a Bathtub
The Basics of Plumbing Skills When Installing a Bathtub
Blog Article
The article in the next paragraphs on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is immensely entertaining. Give it a try and make your own personal final thoughts.
Installing a bath tub isn't precisely rocket science, but it does require strong plumbing, carpentry, and also often, tiling abilities. Changing an old bathtub with a new one is additionally a moderately difficult project. If the old tub is easily obtainable, the task can relocate speedily; if you need to open up a wall to get rid of the old bathtub as well as place the new tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly need a helper to leave the old tub and also set in the brand-new one. Make certain you have qualified on your own for the work and are comfortable attempting it. Rather than hiring a service provider to take control of a halfway-completed task, it is better to consider utilizing one prior to you begin. Chances are you might need a professional plumber to make tube connections.
This post will assist you install a new bathtub in your bathroom if you have actually already gotten a new bathtub as well as do not require to alter the setup of your previous water system pipelines.
Your devices and also product list must comprise the following:
Getting ready for the Installment
Firstly, the supporting framework supplied with the bathroom must be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the faucet comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps system to prevent stress on the tub.
Fit the flexible faucet ports to the bottom of both taps utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be suited its last placement.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, then the first thing you must do is separate the water system. After doing so, switch on the taps to drain any kind of water remaining in the system. The process of removing the existing taps can be quite troublesome because of the restricted access that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will come from the pipelines. When the supply pipelines have been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Prior to proceeding to fit the new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Using the two wood boards under its feet, position the bath tub in the required setting. The wood boards are useful in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be attained by inspecting the level and also readjusting the feet on the bathtub until the level reviews level.
To mount taps, fit the bottom of the furthest flexible faucet port to the proper supply pipeline by making a compression join; then do the same for the various other tap.
Switch on the supply of water and also check all joints as well as brand-new pipework for leakages as well as tighten them if necessary. Load the bath tub as well as likewise check the overflow outlet and also the regular electrical outlet for leakages.
Finally, take care of the bath paneling as described in the maker's instruction manual. Tiling as well as sealing around the tub should wait up until the bath tub has been utilized at the very least when as this will settle it right into its last placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making certain that the washing machines are in place in between the tap and also the sink. Secure the tap in position with the maker provided backnut. As soon as the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind must be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to crack an inflexible seal, causing the water to pass through the wall between the bath as well as the tiling, leading to problems with wetness as well as feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your components and also installations. They are marketed in tubes and cartridges, and also are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to permit the activity experienced when the tub remains in usage. The sealer can crack relatively early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the marketplace. It is recommended to fit the tiles utilizing waterproof or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on How to Install a Bathtub? Write feedback below. We'd be pleased to hear your opinions about this blog entry. We are looking forward to see you back again in the future. Don't hesitate to take the opportunity to distribute this blog posting if you enjoyed reading it. We recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.
We're the solution! Report this page